CE marking requirements explained

Oskar Mortensen Oskar Mortensen
11 min read

Before a toy, an electrical product, a machine or any other product covered by an EU CE law goes on sale, its manufacturer has to prove it complies, sign a declaration of conformity and put the CE mark on it. This guide explains which products need the mark, the six steps from the first check to the finished label, what importers and distributors must verify and who answers for the product when the seller is outside the EU.

An electric kettle with the CE mark on its side, for an article on CE marking requirements in the EU

A product that falls under an EU law requiring CE marking cannot be sold in the EU without the mark, and its manufacturer may only add it after proving the product meets that law (Regulation (EC) No 765/2008).

There is no EU certificate to apply for, because the manufacturer checks the product, keeps the proof and signs for it. Below is which products the CE marking requirements cover, the six steps to meet them, who does what in the supply chain and what happens when the mark is wrong.

Where your company is based decides who answers for the CE mark in the EU.

CE marking at a glance

These six facts frame every requirement on this page.

  • What it is. The manufacturer's sign that a product meets the EU laws that require the mark (Regulation (EC) No 765/2008, article 2(20)).
  • Who may add it. Only the manufacturer or its authorised representative (article 30(1)).
  • Which products. Only those covered by an EU law that asks for the mark, and no others (article 30(2)).
  • Where it counts. Across the European Economic Area, the 27 EU countries plus Iceland, Liechtenstein and Norway.
  • Certificate. No central EU certificate. No EU body gives permission to use the mark.
  • Cost. The mark itself is free, while the testing and assessment behind it are paid by the manufacturer.

The rules come from EUR-Lex's text of Regulation (EC) No 765/2008 and the EU's Your Europe guide to CE marking. For a short definition, see the glossary entry on CE marking.

The one rule behind every CE mark

By putting the CE mark on a product, the manufacturer declares that it takes responsibility for the product meeting every EU law that requires the mark (article 30(3)). Nobody else signs off on that promise.

That is why the European Commission stresses that the mark does not mean the EU or any authority has approved the product as safe. It does not say where the product was made either.

How the same rule reaches every CE product

There is no single CE law. Each product group has its own, such as the Low Voltage Directive for electrical equipment or the Toy Safety Directive for toys, and each one says that its products carry the mark.

Most of those laws follow one EU model, Decision No 768/2008/EC, so their duties look alike. The examples on this page use the Low Voltage Directive, 2014/35/EU.

Two more limits apply to every product.

  • The CE mark is the only mark that proves conformity with these laws (article 30(4)).
  • Look-alike marks are banned. Other logos may sit next to it, as long as the CE mark stays visible and legible (article 30(5)).

Which products need CE marking?

Three questions settle whether the mark applies and how much work it takes.

  1. Does an EU law that asks for CE marking cover your product?

If it does, the mark is required. If no such law covers the product, it must not carry the mark, and for consumer products the General Product Safety Regulation (GPSR) sets the safety rules instead.

  1. Does more than one of those laws cover it?

Some products fall under several at once. The mark goes on only when all of them are met, and a single EU declaration of conformity names every law (Low Voltage Directive, article 15(3)).

  1. Does the law let you check the product yourself?

Some do, such as the Low Voltage Directive. Others require a notified body, typically for higher-risk products such as medical devices, construction products or machinery.

CE laws for common product groups

The table below lists the CE laws behind the product groups sellers ask about most. The EU's own list is longer and also covers lifts, pressure equipment, measuring instruments and more.

Products CE law
Electrical equipment from 50 to 1,000 volts AC Low Voltage Directive 2014/35/EU
Electronics that emit or pick up interference Electromagnetic Compatibility Directive 2014/30/EU
Anything with Wi-Fi, Bluetooth or another radio Radio Equipment Directive 2014/53/EU
Hazardous substances in electronics RoHS Directive 2011/65/EU
Toys Toy Safety Directive 2009/48/EC, being replaced by Regulation (EU) 2025/2509
Machinery Machinery Directive 2006/42/EC, being replaced by Regulation (EU) 2023/1230
Batteries EU Battery Regulation (EU) 2023/1542
Personal protective equipment Regulation (EU) 2016/425
Gas appliances Regulation (EU) 2016/426
Medical devices Regulation (EU) 2017/745

Several of these are directives. Each EU country writes a directive into its own law, so national details can differ, while a regulation applies word for word everywhere.

Who answers for the CE mark in your case

The duties follow a company's role. The manufacturer makes the product, or has it made and sells it under its own name or brand, and answers for the whole product, including parts bought from others.

Established in the EU. If your company makes the product or sells it under its own brand, the manufacturer's duties are yours, whoever built it.

If you import the product from outside the EU, you carry the importer's checks below and put your own name and address on it.

Selling from outside the EU. The manufacturer's duties still apply to you, and for many CE products an EU company must also answer for the product.

Under article 4 of the Market Surveillance Regulation (EU) 2019/1020, that is an EU importer or an authorised representative with a written mandate. Failing both, it falls to an EU fulfilment provider for the products it handles.

That company keeps the declaration of conformity for the authorities and its name and postal address go on the product, its packaging, the parcel or an accompanying document. The rule covers toys, electrical and radio equipment, machinery and batteries, but medical devices are not on its list.

Six steps to put the CE mark on a product

The steps below take a manufacturer from a product design to a product that may carry the mark. An importer or distributor checks the result instead of doing the work.

Step 1. Find every CE law that covers the product

List the CE laws for the product before anything else, because each one sets its own essential requirements, conformity procedure and paperwork.

Check the obvious law first, then the ones a feature brings in.

  • The main law. A kettle sits under the Low Voltage Directive, a doll under the toy rules.
  • Built-in features. Electronics bring in the EMC and RoHS rules.
  • Built-in batteries. These bring the Battery Regulation with them.

Write the list down. It decides every later step and ends up in your declaration.

Step 2. Decide between your own check and a notified body

Each CE law sets the procedure, picked from a fixed menu of modules in Decision No 768/2008/EC according to the product's risks (article 4).

One of them is module A, internal production control. Here the manufacturer checks the product itself and declares on its own responsibility that it complies.

Where the law requires third-party testing, a notified body takes part, an independent organisation an EU country has authorised to assess products.

Diagram of the two routes to the CE mark under EU product law: on the left a factory with its own checklist and the CE mark alone, on the right a factory with a notified body and the CE mark followed by the body's four-digit number

Notified bodies are listed in the EU's NANDO database, by product and law. Watch for so-called voluntary certificates, which the EU says are not valid for CE marking.

Step 3. Build the technical documentation

The technical documentation is the file that proves the product complies. Under module A it holds at least these six things.

  1. A general description of the product.
  2. Design and manufacturing drawings of components, sub-assemblies and circuits.
  3. The explanations needed to understand those drawings and how the product works.
  4. The standards applied. A list of the harmonised standards used, and how each requirement was met where none was used.
  5. Calculations and examinations carried out during design.
  6. Test reports.

It also needs an analysis and assessment of the product's risks. Following harmonised standards published in the EU's Official Journal gives a presumption that the product meets the requirements those standards cover.

Step 4. Sign the EU declaration of conformity

The EU declaration of conformity is the signed statement in which the manufacturer takes responsibility for the product. It follows the EU's model and states:

  • the product's unique identification and a description that allows it to be traced
  • the manufacturer's (or authorised representative's) name and address
  • that it is issued under the manufacturer's sole responsibility
  • every EU law the product meets and the standards used
  • the notified body's name, number and certificate, where one was involved
  • the place and date of issue, and a signature

One declaration covers every CE law that applies. Keep it up to date and translate it into the language each country requires (Low Voltage Directive, article 15).

Step 5. Put the CE mark and the details on the product

Only now does the mark go on, before the product is placed on the market. It must be visible, legible and indelible, on the product or its data plate, or on the packaging and documents when that is not possible (Low Voltage Directive, article 17).

Diagram of an electric kettle under the EU CE marking rules, with the CE mark on its base plate and labels for the type and serial number, the manufacturer's name and postal address, the importer's name and address, and the instructions in the buyer's language

The mark is at least 5 mm high unless the product's law says otherwise, and keeps the proportions of the official drawing (Regulation (EC) No 765/2008, Annex II). Where a notified body checks production, its four-digit number follows the mark.

The product also carries a type, batch or serial number, the manufacturer's name and postal address, and instructions and safety information in a language the buyer understands (Low Voltage Directive, article 6).

Step 6. Keep the product compliant after it is sold

The CE mark speaks for the product on the day it was placed on the market, so the work does not stop there.

Production must stay in line with the documentation, and any change to the design or to the standards used has to be taken into account. When a product turns out not to comply, the manufacturer fixes it, withdraws it or recalls it, and tells the authorities straight away if it presents a risk.

Keep the technical documentation and the declaration for 10 years after the product is placed on the market under the Low Voltage Directive (article 6(3)). Other CE laws can set a different period.

What importers and distributors check before selling

Most CE laws also give importers and distributors a short list of checks, taken from the same EU model.

  • Importers sell only compliant products. They check that the assessment was done, the documentation exists and the mark and documents are in place, add their own name and address, and keep a copy of the declaration.
  • Distributors check the CE mark, the documents and the instructions in the local language before selling, and hold back a product they believe does not comply.
  • Importers or distributors selling under their own brand become the manufacturer, with every duty above. The same goes for one that changes a product in a way that can affect its compliance.

Two CE laws being replaced by 2030

Two of the CE laws for common products are being replaced by regulations, each on a fixed date.

  1. 20 January 2027. The Machinery Directive 2006/42/EC applies until this date. The Machinery Regulation (EU) 2023/1230 replaces it.
  2. 31 July 2030. The Toy Safety Directive 2009/48/EC applies until this date. The Toy Safety Regulation (EU) 2025/2509 replaces it.

The European Commission has also evaluated the framework behind CE marking and concluded it should explore whether an update is needed, including a digital CE marking. That is a finding of the evaluation, not a decided rule.

Fines and enforcement for a wrong CE mark

There is no EU fine for CE marking. Each country must make sure the mark is used correctly, act when it is misused and set its own penalties, which may include criminal sanctions for serious cases and must fit the seriousness of the offence (article 30(6)).

National market surveillance authorities can check any product on the market and ask the company for all the information and technical documentation behind its CE mark.

These are four ways a CE-marked product can break the rules.

  • A mark without the work. The mark is on, but the documentation or declaration is missing.
  • A mark where no law asks for one. That breaks article 30(2) as much as a missing mark does.
  • A look-alike logo that can be confused with the CE mark.
  • No EU contact on a product from outside the EU that needs one.

A good first check today is to list each product's CE laws and confirm that an EU company is named on everything you sell from abroad.

Where Repax fits next to CE marking

CE marking is the manufacturer's work, and only parts of it can be handed to an authorised representative. The same products also bring separate extended producer responsibility (EPR) duties for their packaging, and electrical products and batteries carry EPR duties of their own.

Those EPR duties mean a registration, reports and fees in each EU country where you sell, as the guide to EPR registration in Europe explains.

Repax does not test products, draw up technical documentation, sign declarations of conformity or act as a CE authorised representative. Those stay with the manufacturer and its EU partners.

Not sure if you are registered in every country you sell in?

We will run a demo on a representative product and discuss your specific EPR mix.

Frequently asked questions about CE marking requirements

Below are the eight questions sellers ask most about CE marking requirements.

What does CE marking mean?

It means the manufacturer declares that the product meets every EU law requiring the mark and takes responsibility for it (Regulation (EC) No 765/2008, article 30). It is not an EU approval and says nothing about where the product was made.

Is CE marking a certificate?

No. No central EU body issues CE certificates or permission to use the mark. The manufacturer checks the product and signs a declaration of conformity. Where the law requires a notified body, its certificate is one step on the way, not the mark itself.

Which products need CE marking?

Only products covered by an EU law that requires the mark, such as electrical equipment, electronics, radio equipment, toys, machinery, batteries, protective equipment, gas appliances and medical devices. A product that no such law covers must not carry the CE mark.

Who is allowed to put the CE mark on a product?

Only the manufacturer, or its authorised representative on its behalf (article 30(1)). An importer or distributor that sells the product under its own brand, or changes it in a way that can affect its compliance, takes on the manufacturer's duties.

Do I need a notified body for CE marking?

Only if your product's law requires one. Some laws, such as the Low Voltage Directive, let the manufacturer check the product itself. Higher-risk products, such as medical devices, construction products and machinery, typically need a notified body, listed in the EU's NANDO database.

How big does the CE mark have to be?

At least 5 mm high, unless the product's own law sets another size, and in the proportions of the official drawing (Regulation (EC) No 765/2008, Annex II). It must be visible, legible and indelible, on the product or its data plate where possible.

Does CE marking expire?

No. The mark covers the product as it was when placed on the market. The declaration of conformity and technical documentation must be kept up to date when the product or the rules change, and stored for 10 years under the Low Voltage Directive.

Does a seller outside the EU need an EU company for CE products?

For many CE products, yes. Article 4 of the Market Surveillance Regulation requires an EU importer, authorised representative or fulfilment provider to hold the declaration and answer the authorities, and its name and postal address must appear on the product, packaging or parcel.

Written by

Content specialist at Repax.io

I translate sustainability regulations by day, chase golf balls by evening. Both involve more rules than anyone admits.